VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Starter Vape Kit  /  Starter Vape Kit lead time slip — with QC photos
starter vape kits · private label sellers

Starter Vape Kit lead time slip — with QC photos

We work with private label sellers who order between a few hundred and a few thousand units at a time, and we treat both ends the same way: a written specification, a sample you approve, and a production run that matches the sample.

Published 02 May 2025  ·  VapeWholesaleHub  ·  Reading time 8 min

Surface finish under raking light, one of the cosmetic checks.
Surface finish under raking light, one of the cosmetic checks.
Close inspection of the assembly line before the batch is released.
Close inspection of the assembly line before the batch is released.

What we test before a carton is sealed

A starter vape kit programme only works when three numbers agree: your shelf price, your reorder cycle and your defect tolerance. Change one and the plan moves. We build assortments around those three and we say so up front rather than after the invoice.

Leak complaints almost always trace back to one of three things: an over-torqued centre post, a seal that sat in a hot container, or a fill volume pushed past the design limit. We cap fill volume slightly below maximum for exactly that reason.

A 0.5 percent defect rate sounds excellent until it lands on a 600 unit order and you are handling three returns in a week. We quote realistic rates per category and we credit in advance for the known failure modes.

Getting the documents right

Regulation for starter vape kits differs by country and sometimes by state. We do not pretend to be your lawyer, but we do keep the document pack current and we will tell you when a configuration cannot legally enter a market you have named.

Advertising rules are stricter than product rules in most markets. Claims about cessation, health or comparative performance should stay off packaging and off your product pages unless your legal team has signed them off.

For private label sellers, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

Where the margin really sits

Payment terms for new accounts are normally a deposit with the balance against the bill of lading. Established buyers on a repeat schedule can move to terms after three clean shipments.

Unit price breaks usually land at 300, 800 and 1600 pieces. Between those steps the cost curve flattens, which is why pushing a 200 unit order to 500 often costs less per unit than buyers expect.

  • Specification locked in writing before production starts
  • Private label files archived for future rebrands
  • Batch codes traceable from carton back to production date
  • Consolidated or split shipping, quoted both ways
  • Named account contact who has handled the product
  • Mixed SKU cartons to spread first-order risk

Turning shelf space into repeat visits

Photography matters for online listings. Shoot on a neutral background with the device at a slight angle, show the pack alongside the unit, and keep the same framing across the range so the grid reads as a family.

Staff knowledge converts better than any poster. If your team can explain the difference between two coils in one sentence, the step-up SKU sells itself.

Specification summary

Typical specification for this category
Battery350 mAh
Pod capacity3.0 ml
Coil resistance1.0 ohm
IncludedDevice, 2 pods, cable
ChargingUSB-C 5V/1A
PackagingBlister pack
Minimum order300 units per SKU, mixed cartons allowed
Lead time25 working days after artwork approval

If any of this is unclear, the fastest route is a message rather than a meeting. Send the market you sell into and the price band you work in, and you will get a specific answer instead of a brochure.

Frequently asked

Do you support private label?

We do. Send your artwork or your brand direction and we will return a digital proof, then a physical dummy for colour approval. Packaging files stay on record so a rebrand later is a file update rather than a redesign.

How long does production take?

Around 15 working days after artwork approval for stock configurations, plus transit. Custom runs add roughly a week for tooling and a physical dummy. We confirm the date in writing on the order acknowledgement.

What happens if part of the order is defective?

Report within seven days with photos and the batch code. Confirmed defects are replaced or credited on the next shipment. The failure is logged by mode and batch, and reviewed monthly with the factory.

Related reading

Need a quotation on starter vape kits?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on starter vape kits

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us