VapeWholesaleHub  |  Wholesale supplier · Shenzhen, China
Tel / WeChat / WhatsApp: +86 13711127975  |  vape@0099933.xyz
Home  /  Starter Vape Kit  /  Starter Vape Kit battery and cell sourcing checklist
starter vape kits · private label sellers

Starter Vape Kit battery and cell sourcing checklist

Buyers come to us for starter vape kit after a bad quarter: dead stock on one side, empty shelves on the other. The cause is usually the same, an assortment built from a catalogue instead of from sell-through data. This page explains how we rebuild that balance for private label sellers.

Published 03 September 2026  ·  VapeWholesaleHub  ·  Reading time 9 min

Carton-ready units from the same batch, coded for traceability.
Carton-ready units from the same batch, coded for traceability.
Starter Vape Kit battery and cell sourcing checklist configuration from a production run, photographed before packing.
Starter Vape Kit battery and cell sourcing checklist configuration from a production run, photographed before packing.
Finish and assembly detail checked against the approved reference sample.
Finish and assembly detail checked against the approved reference sample.

Assortment planning without the guesswork

Starter Vape Kit sits in a crowded price band, and the cheapest quote on the sheet is rarely the cheapest unit on your shelf. Everything below is built around reorder rate, defect rate and cash conversion rather than headline unit price.

Factory capacity matters more than factory size. A line that can hold a tolerance across 5,000 units is worth more than a showroom that can produce 50,000 on paper. We qualify capacity by running a repeat order and measuring the drift.

We keep a short list of approved configurations for starter vape kits. Anything outside that list is possible, but it becomes a custom run with a custom lead time, and we quote it as such rather than pretending everything is standard.

Getting the documents right

Age verification is not only a website problem. Retail packaging, shelf placement and staff scripting all carry compliance weight, and auditors increasingly ask for evidence of all three.

If you sell into a market that requires child-resistant packaging, say so at quotation stage. Retrofitting a CR closure onto a finished bottle design usually means a new mould and a four week delay.

For private label sellers, the practical answer is usually a shorter range: two core lines, one step-up, one trial SKU. Everything else is inventory risk wearing a nice finish.

After-sales, replacements and reorders

We keep the specification sheet for every order on file. Two years later, when a customer asks whether a pod is compatible, the answer is a lookup rather than a guess.

Technical questions usually arrive at the worst possible moment, which is why we answer them on WhatsApp as well as email. A photo and a two line message resolves most issues faster than a ticket.

  • Named account contact who has handled the product
  • Standing reorder schedule with a fixed cut-off
  • Batch codes traceable from carton back to production date
  • Artwork proof plus physical dummy for custom packaging
  • Seven-day defect reporting with replace-or-credit
  • Consolidated or split shipping, quoted both ways

What we test before a carton is sealed

Leak complaints almost always trace back to one of three things: an over-torqued centre post, a seal that sat in a hot container, or a fill volume pushed past the design limit. We cap fill volume slightly below maximum for exactly that reason.

Cosmetic grading is written down, not argued about. Minor scuffs inside the tolerance band are accepted; anything that would make a customer put the unit back on the shelf is rejected. Your staff should never have to explain a finish defect to a paying customer.

Specification summary

Typical specification for this category
Battery800 mAh
Pod capacity3.0 ml
Coil resistance0.8 ohm
IncludedDevice, pod, cable
ChargingUSB-C 5V/1A
PackagingRetail box
Minimum order300 units per SKU, mixed cartons allowed
Lead time12 working days after artwork approval

The detail above is what we hold ourselves to on every shipment, including the small ones. It is also the list we will walk through with you before the first order.

Frequently asked

How long does production take?

Around 20 working days after artwork approval for stock configurations, plus transit. Custom runs add roughly a week for tooling and a physical dummy. We confirm the date in writing on the order acknowledgement.

What happens if part of the order is defective?

Report within seven days with photos and the batch code. Confirmed defects are replaced or credited on the next shipment. The failure is logged by mode and batch, and reviewed monthly with the factory.

Can you ship to multiple locations?

Yes. Split shipments are quoted separately because consolidation and splitting price differently. Tell us the destination list at quotation stage and we will show both options.

Related reading

Need a quotation on starter vape kits?

Send destination market, target price and quantity. Same-day reply on working days.

Tel / WeChat / WhatsApp +86 13711127975  ·  vape@0099933.xyz

Talk to the supply team

Ask for a quotation on starter vape kits

Tell us the market you sell into and the price band you work in. You will get a specification and a landed cost estimate, not a catalogue dump.

What to send

Destination market, target retail price, quantity per SKU, and whether you need private label. With those four lines we can quote the same day.

Samples ship by air express and the cost is credited against your first production order.

Email the team
WhatsApp Email us